Cartiglio A4 Autocad 2016

суббота 05 январяadmin
Cartiglio A4 Autocad 2016 Rating: 5,6/10 4596 reviews

Introduction

For example: You need to print a drawing AutoCAD for customer or for myself with requirement as following: Paper size: A1 (ISO 594x841mm) Color: white and black. Layer: use object lineweight. Screening: 100%. Printer: DWG to PDF. Step 1: Open your drawing that you need to print.

There has alwas been some confusion over the size of standard ISO drawing sheets with AutoCAD.The stated sizes in the plot dialogue box are not the true ISO sizes, rather they relate to the plotted area on standard size cut sheets. Obviously it is not possible to print right to the edge of cut sheets, so the AutoCAD sizes quoted are always smaller than the true cut sheet size. See the 'Paper Size' dialogue box on the right.

To some extent this issue has been physically resolved by the use of roll feed plotters. For example, a true A3 print can be made from an A1 roll. Despite this fact, AutoCAD still quotes the plotted area sizes in the plot dialogue box. If you look at the dialogue box above, you will see that it is possible to enter your own 'USER' paper sizes which can be set as true ISO sizes. In this example the 'USER' size has been set to A3. Use the sizes in the table below, which are the true ISO cut sheet sizes as a guide.

Paper sizes in millimetres
A01189x841
A1841x594
A2594x420
A3420x297
A4297x210
A5210x148

The ISO paper sizes are devised in such a way that each smaller size is exactly half the size of the previous one. For example, cutting an A3 sheet in half so that the cut is perpendicular to the longest side would result in two A4 sheets. See the illustration above.

Drawing ISO Sheets in AutoCAD

The simplest way to draw drawing sheet outlines is to use the Rectangle command, picking the lower left hand point and then entering a relative co-ordinate for the upper right.

For example

To draw an A3 sheet:

  1. Start the Rectangle command, type RECTANG at the command prompt, pick 'Rectangle' from the 'Draw' pull-down or click on the button.
  2. At the Chamfer/Elevation/Fillet/Thickness/Width/<First corner>: prompt, pick a point somewhere in the lower left of the drawing area.
  3. At the Other corner: prompt, enter a relative co-ordinate using the appropriate drawing sheet dimensions, type @420,297 and right click orat the keyboard.
  4. Your drawing sheet outline will now be drawn at the correct size. If you cannot see all of the rectangle, use Zoom Extents to view the whole thing. You can do this by typing ZE at the keyboard (Z is the keyboard shortcut for the Zoom command).

Drawing Scaled ISO Sheets

The drawing sheet sizes in the table above can easily be used to draw sheet outlines in Paper Space since plotting from Paper Space should always normally be at a scale of 1=1 and Paper Space drawing units should be equivalent to millimetres. However, drawing sheet outlines in Model Space is rather more complicated because you need to take into account both the intended plot scale and the drawing units (which may not be millimetres). Fortunately there is a straightforward formula which you can use to determine the actual size of your required sheet outline in drawing units.

Drawing Units per metre x Scale x Sheet Size in metres

Tranceport

For example

An A3 sheet at 1:200 and drawing units in millimeters can be calulated as follows:

1000 x 200 x 0.420 = 84000
1000 x 200 x 0.297 = 59400

An A3 sheet at 1:500 and drawing units in metres can be calculated as follows:

1 x 500 x 0.420 = 210.0
1 x 500 x 0.297 = 148.5

Plotting from Model Space

The only other consideration you need to make when plotting in Model Space is the plotting scale. This will be different depending upon which drawing units you are using.Working in millimetres is straightforward because you can use the actual scale in the Plot dialogue box since plotted units are also in millimetres. For example, a drawing to be plotted at 1:500 with drawing units in millimetres will have a plot scale of 1=500. Working in metres is a little more complicated. You will need to divide the scale by 1000 to get the correct figure. For example, a drawing to be plotted at 1:500 with drawing units in metres will have a plot scale of 1=0.5 which is 1000 times smaller than the figure for millimetres because there are 1000 millimetres in a metre.

Common Plot Scales
Plot ScalePlotted MMDrawing Units
1:201=0.02
1:501=0.05
1:2001=0.2
1:5001=0.5
1:12501=1.25
1:25001=2.5

The table above lists a number of common plot scales and their corresponding plot scale factors which should be used when plotting from Model Space and when drawing units are in metres.

Donate to CADTutor

If you found this tutorial useful, you might like to consider making a donation. All content on this site is provided free of charge and we hope to keep it that way. However, running a site like CADTutor does cost money and you can help to improve the service and to guarantee its future by donating a small amount. We guess that you probably wouldn't miss $5.00 but it would make all the difference to us.

Welcome to autocadtip.com AutoCAD tutorial

In this series, we are going to learn lesson about how to print in AutoCAD. Here, we will give a tutorial to you follow example specifically.

For example:

You need to print a drawing AutoCAD for customer or for myself with requirement as following:

Paper size: A1 (ISO 594x841mm)

Color: white and black

Layer: use object lineweight

Screening: 100%

Printer: DWG to PDF

Step 1: Open your drawing that you need to print.

Step 2: Install already printer in AutoCAD software.

Step 3: Go to File > Plot or using shortcut is Ctrl + P > show Plot option box.

Step 3: Plot option in AutoCAD

Step 4: Choose DWG to PDF printer.

Step 5: Choose plot style is monochrome.ctb > click edit plot style > show Plot style editor option box > click Form view > choose all color > assign screening = 100 and lineweight = use object lineweight > click save & close button.

Step 5: Choose Plot style in AutoCAD

Step 5: Choose edit button of Plot style in AutoCAD

Step 6: Choose Drawing orientations is landscape.

Step 6: Choose drawing orientation when print

Step 7: Choose Plot scale is fit to paper.

Step 7: Choose Plot scale when print drawing in AutoCAD

Step 8: Choose Plot offset is center the plot.

Step 9: Choose Plot area, click window > pick first corner > pick second corner > show plot option again.

Step 9: Choose Plot area when print in AutoCAD

Second corner

Step 10: Press Apply to layout > Preview button to see drawing before printing.

Step 10: Preview drawing before printing in AutoCAD

Step 11: Click right of mouse > choose Plot.

So we have finished step to print a drawing AutoCAD, good successful to you!

More from my site

Sheet Set Manager feature tutorial basic in AutoCAD 2018
Table Ideas for Coffee Shop – Surface circle, three legs shape trapezoid #6
How to export from microsoft project to AutoCAD drawing
Tip how to fix error broken concrete hatch pattern
Select object tutorial with Quick Select feature in AutoCAD
Update some new features AutoCAD 2016